Home > Error Code > Wd Hard Drive Error Codes

Wd Hard Drive Error Codes

Contents

This may be due to a defect with the drive or a bad connection. to report if a drive has failed, it must be enabled as a system option. Reply With Quote 03-27-2009,12:43 AM #3 duskfall View Profile View Forum Posts View Blog Entries View Articles Neophyte Geek Join Date Mar 2009 Posts 2 Thank you for the info! Re-test Drive 201 Non-WD Drive The drive does not have a WD serial number. http://maxspywareremover.com/error-code/wd-hard-drive-error-36.php

This test gives me an error 0226 Sector Relocation Error The official recommendation is to replace the drive. Replace the drive if the error repeats. You haven't actually specified which option is being suggested to swap. Retest after checking the connections.

How To Fix Error Code 2000-0142

Retest. Replace the drive if the error repeats. Re-test Drive with appropriate diagnostic utility 133 Illegal ID FW overlay not found.

After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 00 00 00 00 40 Commands leading to the Re-Test Drive 107 Check Sum Error Accumulated test data on the drives is corrupted. Insert your OS disk into your cd/dvd drive As the machine boots up - it should have an option to hit F2 or F12 Hit the F12 key This will give Hard Drive Error Code 2000-0146 Drive should be replaced.

Please re-test the drive with Data Lifeguard. Hard Drive Error Code 0142 Repair Tip Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status. The drive has to be replaced. http://support.wdc.com/knowledgebase/answer.aspx?ID=251 Replace the drive if the error repeats.

The more you work the drive, the more and more of a risk you will have to lose data without professional help in the thousands of dollars.Keep in mind the parts Dell Hard Drive Error Code 0146 Let us know if it worked. [ Book mark this post to find it again] AntiX-15, Win 7 and Win 10 Reply With Quote September 8th, 2008,04:50 PM #3 videobruce View He has a Dell desktop, and was performing a regular Windows update when his computer froze in the middle of the update. The drive is defect free.

Hard Drive Error Code 0142 Repair Tip

This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Re-test Drive 141 UNKNOWN ERROR An unknown error has occurred during testing. How To Fix Error Code 2000-0142 Check cabling and retest. Dell Validation Code Return to Top Data Lifeguard Tools 11 and 10 Error Codes Note: If the same error code is encountered more than once after re-testing, please Contact Us for additional assistance.

If you have an unrecoverable problem, determine if it is under warranty.-- If under warranty, start the RMA process-- If not under warranty, proceed to step 77. his comment is here This condition occurs when the device's SMART reliability status indicates an impending degrading or default condition. The drive has not responded in the time allotted. The ATA Spec does not define SMART I, II, III. Dell Hard Drive Error Code 2000-0151

Replace the drive if the error repeats. in your hard drive. Check connections and retest. this contact form Retest the drive.

Now, coincidences do happen but I can't help thinking they put an iffy 'refurb' drive in that they hoped would last longer that the warranty, rather than a new drive. Dell Error Code What is an instant of time? This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection.

This sounds much more like a poor or loose (either data or power) cable/connection to the HDD or even a faulty PSU.

SMART III: Not defined by any industry standard specification. failure and errors Answer ID 251 This answer explains about S.M.A.R.T. At least ten ECC errors have been detected. Dell Validation Code Generator May need to run DLGUDMA to set the drive to a slower speed or replace the IDE cable.

It is also possible to see this error on defective Western Digital drives. Replace the drive if the error repeats. This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc. http://maxspywareremover.com/error-code/wd-hard-drive-error-code-36.php Replace the drive if the error repeats.

It also may be due to a defective connection. ECC is a hardware correction technique that corrects errors. it worked for me cheers Reply With Quote 04-16-2012,04:21 PM #23 f1rebolt View Profile View Forum Posts View Blog Entries View Articles Neophyte Geek Join Date Apr 2012 Posts 2 Thanks Version 4.12 for older drives and version 5.00 for current drives.

It also may be due to a defective connection. Check cabling and retest. Replace the drive if the error repeats. There may be repairable media errors on a platter.

Selective Self-test supported.