Home > Error Codes > Whirlpool Elite Washer Error Codes

Whirlpool Elite Washer Error Codes

Contents

Press 'Stop/Cancel' to clear display. If failure still present: 3. For SELF CLEAN models, check door lock operation. Opening the lid will allow you to redistribute the load to avoid a further off balance error. click site

Okay Or call now for immediate assistance: 1-800-252-1698 Note: new item(s) added to cart Part Name Price: Quantity: Continue shopping View Cart and Checkout More Accessories Subscribe today and receive: FREE Check the drain pump filter for foreign objects. 5. F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down. Loading...

Whirlpool Duet Washer Error Codes F21

Located on the bottom of the door latch assembly is a tear-drop shaped tab. 5. F02 - Long Drain (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code. This may indicate a bad pump, an extra heavy load, excessive detergent or excessive suds.

Check/clean drain pump filter of foreign objects. 5. NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. As a member of Shop Your Way Rewards℠, you'll earn Rewards every time you shop. Whirlpool Duet Washer Error Codes F02 But I’m here to show you that in 99.9999% of these cases, the board itself is perfectly functional but the real problem is the CONNECTIONS to the board. “Uhh, howzzat, Samurai

You usually hear the dispenser system shifting constantly before this code is displayed. Whirlpool Duet Washer Error Codes F20 Check wire harness connections to the drain pump, pressure switch, water inlet value, and Central Control Unit (CCU). 4. Check wires and connectors from control to door switch, then from door switch to control. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4

The washer does not flash "PF" when it is first plugged in. Whirlpool Duet Dryer Error Codes Sr Stuck relay "Sr" signifies a failure of the relay in the closed position. Had been told was motor control board. $200 in parts & $130 in labor. I fixed my Duet thanks to you.

Whirlpool Duet Washer Error Codes F20

Check mechanical linkage from dispenser motor to the top of the dispenser. 3. F6E2 and F6E3 Errors - Communication fault Communication fault between the main control board (CCU) and the user interface (UI) unplug and check the wire connections between the washer's (CCU) and Whirlpool Duet Washer Error Codes F21 FdL Door lock error A Door Lock Error occurs if the door cannot be locked. Whirlpool Top Load Washer Error Codes The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.

Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU get redirected here Once the F2 code appears, select 'cancel' and observe for one minute for errors. Unplug unit and disconnect power. Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation. Whirlpool Duet Reset

Check connections of the CCU board within the housing. This should clear the unit of the excess detergent. Unplug the washer and, if the washer is overfilled, check the water inlet valve assembly for proper shut-off of water flow. navigate to this website F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED.

Replace failed component. Whirlpool Washer Error Codes 5d Replace failed component. Exchange Steamer if it is totally blocked.

Reply Rachel says: October 14, 2015 at 4:34 pm thanks I thought the explanation and the video helped a lot compared to previous tips that didn't last long.

Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. Press PAUSE/CANCEL two times to clear the display. 1. Er Processor reset error This error code is displayed if the control failed to save cycle information during a power failure. Whirlpool Duet Sport Washer Error Codes FL - Flood Condition - FL error code will appear when the unit detects an overfill, or excessive amounts of water in tub.

The tines can become loose or the pads on the board may become oxidized. Check resistance of heating element, if present on this model. (abnormal = infinity) 4. F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). http://maxspywareremover.com/error-codes/whirlpool-washer-troubleshooting-error-codes.php Check wires and connectors from control to latch switch, then from latch switch to control.

Copyright © 1999-2016 , Eldis Group Partnership. The resistance of both door coils (between pin 1 and 3) should be approx. 320 Ω.