Home > Error Codes > Whirlpool Washer Troubleshooting Error Codes

Whirlpool Washer Troubleshooting Error Codes

Contents

F26 DOOR SWITCH ERROR If the door has not been opened for 3 consecutive cycles or the door switch is open while the door is locked for more than 5 seconds. F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle. rL LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE If at the start of the CLEANING WASHER cycle a load is detected inside the drum. Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. navigate to this website

Learn More for questions or assistance, call 1-800-252-1698 (Se Habla Español) M-F6:30 a.m. - 10:00 p.m. F09 Overflow condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. It fills up with water but won't agitate, spin or drain. DudeWhitman 49,081 views 3:56 Troubleshooting and Repairing an F/dL Error Code on a Whirlpool Duet Washer - Duration: 5:10. http://applianceassistant.com/Washer-Repair/Duet/Duet-Washer-Error-Codes.php

Whirlpool Top Load Washer Error Codes

Replace probe if all else checks out ok. Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit Has the laundry been placed unevenly in the machine?

Int The cycle was paused or canceled.The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time. If during one wash cycle 4 undervoltages occur then a Motor Control Unit failure is displayed. 1. Unplug washer or disconnect power. 2. Whirlpool Duet Dryer Error Codes Continue Reading Keep Learning What are some of the error codes on a Whirlpool Duet washer?

To remove the code, press pause or cancel button twice and the power button once. Whirlpool Duet Washer Error Codes F21 Noel says : Reply August 19, 2016 at 11:12 am The model is AWO/D 42880 what is the fault when the Service red light is blinking. By accepting Shop Your Way member benefits and offers, you agree to the Shop Your Way terms and conditions, available at www.shopyourway.com/terms..

Thank you in advance, Zorica Constantine says : Reply October 1, 2016 at 7:05 pm Hello, thanks for the video.

What does this mean 500 series 9000464931Reply 90 DIY Project Help Tips March 11, 2016 at 9:41 pmjudy, Bosch error code E is an error that means your main control board Whirlpool Duet Washer Error Codes F02 Check the water temperature sensor and connection to it. May 11, 2016 Window Air Conditioner Cools Then Quickly Turns Off May 10, 2016 10 Reasons Your Dishwasher Leaves White Film On Glasses And Dishes May 9, 2016 Samsung Dryer Runs Overloading the unit may cause this problem.

Whirlpool Duet Washer Error Codes F21

Press STOP/CANCEL to clear the display. What does this mean and how do I rectify it, ThanksReply 119 DIY Project Help Tips January 6, 2016 at 1:25 amLynden, Is your washer filling with water? Whirlpool Top Load Washer Error Codes Close the lid and press START to continue with the cycle. Whirlpool Duet Reset Credit will be issued for the part(s) plus tax, minus shipping charges.

Reach up along the inside of the front panel and locate the bottom of the door latch assembly. 4. useful reference F2 Oven temperature is too high 1. None of the buttons on the control pad work. F1E2 Error - Motor control fault. Whirlpool Duet Washer Error Codes F20

Unplug the washer and open the door and there you will see the door lock hole. September 8, 2016 How Many BTUs Will You Need To Cool A Room With An AC? Does the lid lock? my review here Q: Where can one find LG washer parts at a discounted price?

Error codes are two digit combinations not 3, 4, or 5. Whirlpool Duet Sport Washer Error Codes If the above does not correct the problem, go to step 7. 7. The display shows E3.

Sears Holdings reserves the right to terminate or modify this offer at any time for failure to comply with its terms and/or due to any operational malfunction of the software, hardware

CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once. F63 TOTAL STEAMER FAILURE If this Failure is displayed, one or several vital values are out of range. June 24, 2016 Stove Top Temperature Control Knobs - What Do The Numbers Relate To? - Low, Medium, High June 21, 2016 Window Air Conditioner Leaking Water Into House - What Whirlpool Washer Error Codes A10 F22 DOOR LOCK ERROR After 6 failed attempts to lock the door.

Potential Causes • Door Lock Mechanism broken or removed from the Door • Check Door Lock/Switch Assembly • Check the wire harness connections to the Door Lock/Switch Assembly and Central Control The best way I have found to deal with the water when your washer's drain pump isn't working is to use a shop vac and pull from the drain hose. Find Parts ^ top Appliance Repair Appliance Repair Dishwasher Repair Garbage Disposer Repair Dryer Repair Freezer Repair Microwave Repair Range / Oven Repair Range Hood Repair Refrigerator Repair Trash Compactor Repair get redirected here This may mean that you have a clogged water hose inlet screens or an issue with the water inlet valve.

It is an upside F followed by an E. Verify CCU operation by running a Diagnostic Test or any cycle. Potential Causes • Check mechanical linkage from dispenser motor to the top of the dispenser. • Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) • Check It also means unplug the washer so you don't get electrocuted!

This code will also appear if the user presses the START key while the lid is open. Unplug washer or disconnect power. 4. Average current trip occurs if there is a 2 second average of current draw greater than 5.55 Amps at the motor windings. F2 will appear.

If the washer is not draining properly check the drain hose for kinks or clogs. F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC There is no cancel/pause button on the washer. Opening the lid will allow you to view and redistribute the load.