Home > Error Codes > Whirlpool Washers Error Codes

Whirlpool Washers Error Codes

Contents

Reach through the open panel and up to the door lock. codes except F1-E3. Check wires and connectors from control to door switch, then from door switch to control. If failure occurs during high-speed spin the door unlocks after 3 minutes. 1. http://maxspywareremover.com/error-codes/whirlpool-washers-error-codes-duet.php

This may signify problems with the drive motor, thermal protector or motor controller. Check for stuck lock switch. Can you give us the model number of your Whirlpool washer so we can help further? -RRReply 127 Beni December 12, 2015 at 1:40 pmE3 error code flashing on my Scanfrost Turn off hot and cold water to faucets and unplug the unit before proceeding.

Whirlpool Duet Washer Error Codes F21

F5 - E1 Self clean latch will not lock F5 - E2 Latch during CLEAN error F5 - E5 Self clean temperature not reached within 45 minutes. Re-apply power and observe for at least one minute. 3. Performing a reset on the washer may resolve the LE error. October 11, 2016 What Is The Best Way To Fix A Squeaky Door Hinge?

F5 - E6 Door is open, but latch is locked F5 - E7 Self clean latch will not unlock F6 - E0 Return line not connected If switch pulse return line F09 - Overflow Condition (Pressure Switch Closed Too Long) - Check to make sure drain hose is not plugged or kinked and unplug the unit and disconnect power. The control should not allow the unit to run in this condition. Whirlpool Duet Washer Error Codes F02 Re-apply power.

The motor control board (MCU) has attempted to reset several times and does not like the result. (Duet Washer Motor Tests) F2E3 Error - Cycle fault. Any ideas?Reply 47 DIY Project Help Tips June 7, 2016 at 9:59 pmPaul, Make sure your hot and cold water faucets are turned on. F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC hop over to this website Int The cycle was paused or canceled.The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time.

F22 DOOR LOCK ERROR After 6 failed attempts to lock the door. Whirlpool Duet Dryer Error Codes This may indicate a bad pump, an extra heavy load, excessive detergent or excessive suds. If the above does not correct the problem, go to step 7. 7. Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the

Whirlpool Duet Washer Error Codes F20

The control should not allow the unit to run in this condition. SL Suds lock The motor controller senses a suds lock condition by analyzing the current draw on the drive motor. Whirlpool Duet Washer Error Codes F21 Also check for any causes of high resistance in the oven temperature sensor circuit. Whirlpool Top Load Washer Error Codes Replace CCU board.

If a failure occurs during high-speed spin, the door unlocks after 3 minutes. 1. http://maxspywareremover.com/error-codes/whirlpool-wfw8300sw00-error-codes.php Check the harness between the Steamer and the Steamer Electronic board. 3. It is a Chinese brand and is not very reliable. Notify me of new posts by email.{ 3 trackbacks }Samsung Top Load Washer Model WA5471 WA5451 Troubleshooting August 20, 2015Samsung Washing Machine Error Fault Codes | RemoveandReplace.com January 21, 2016LG Washing Whirlpool Duet Reset

Check probe. Possible Causes/Procedure Door lock mechanism is broken or removed from door. What is error code for? my review here Unplug washer or disconnect power. 2.

Note: Applies to all F1-E... Whirlpool Washer Error Codes A10 Do you know what this might be please.Reply 41 DIY Project Help Tips June 22, 2016 at 1:37 pmKeith Vause, Please check our Midea Washing Machine Error Codes page for error Open the lid or press STOP/CANCEL to clear the display.

F03 HEATER SC TO GROUND The Heater has a internal short circuit.

Ask your question below and we will be happy to assist.Related DIY Articles That May Assist You... Sign in Transcript Statistics 65,868 views Like this video? Offer valid for online purchases only. Whirlpool Duet Washer Error Codes F H Note: Double ovens will have two of each switch and one common wire. 2 Digit Failure Codes F0 - Control Board Failure - Replace control board (clock).

WHIRLPOOL FAULT CODES Whirlpool Duet Front Loading Gas and Electric Dryer Fault Codes Failure Code Fault Code Description Solution PF Power failure "PF" flashes to indicate that a power failure occurred Loading... Follow ApplianceAssistant on Twitter! About Appliance Repair Safety Legal Stuff Sponsor a Child => Future Hope Ministries Copyright Appliance Assistant, LLC. 2015 Skip to main content ChatFind a RetailerFAVORITESProductsLaundryWashersDryersWasher/Dryer PairsWasher/Dryer get redirected here Potential Causes • Door Lock Mechanism broken or removed from the Door • Check Door Lock/Switch Assembly • Check the wire harness connections to the Door Lock/Switch Assembly and Central Control

Make sure there is not a siphon problem and check all hoses for possible leaks. Measure door switch (door open = switch open small low voltage terminals). Article type topic Brand Multiple Media article Topic assistance Tags Front Load Washer © Copyright 2016 Whirlpool Home Appliances Powered by MindTouch skip navigation Click to Call Click to Chat F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down.

Press and hold any key to clear the error code and F2 code should appear. Exchange steamer electronic board if valve is OK. Replace CCU board. See this page for more help.

Before this started happening, during washing, the machine would stop at rinse or spin cycle. Select the 'cancel' function and wait 60 seconds. After disconnecting power to the unit, try scraping this coating off the pins. • Check the resistance values between the serial communications pins with the connectors in place. C.

If none of this works you may have an issue with the water inlet solenoids. F/10 Motor control board overheated Unplug the washer and check the wiring connections on the motor control board. Once the “Drain and Spin” cycle completes, the door should unlock. Even after unplugging and the replugging.

Check door switch/lock unit for foreign objects. 2. I feel I have sufficiently checked the wiring harnesses and was thinking that the control board was the last culprit, but hoped for a bit of agreement before I drop the Check wire harness connections to the User Interface and the Central Control Unit. 3. Please check back in a few minutes.

For repair how-to help, visit the PartsDirect repair help section, which includes repair help for washing machines, other major appliances, lawn and garden equipment, garage door openers, vacuum cleaners and more.