Home > Western Digital > Western Digital Diagnostic Error 0132

Western Digital Diagnostic Error 0132

It referred to a hard drive issue and mentioned S.M.A.R.T. (sorry, I didn't write down the exact message). The open file operation will fail with error -1032 (0xfffffbf8). Suspend Offline collection upon new command. Re-Test Drive 105 BUSY GLITCH The drive did not properly respond to test commands. weblink

This may be due to a media or read/write error. An error was reported by the drive during the Write command (to cause the auto-relocation) or the Read Verify command (to verify the relocation happened). Skip to content Advanced search Board index ‹ Hardware/Software ‹ Tech Support Change font size Print view FAQ Register Login Western digital hdd command error 0132 Get your PC tech problems Sense: No additional sense information[ 79.446733] end_request: I/O error, dev sdb, sector 0[ 79.446741] ata1: EH complete[ 79.446964] ata1.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0[ 79.446966] ata1.01: BMDMA https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

What exactly should I try next? (Fortunately there's nothing of particularly great value stored on this drive.) Last edited by Jorpho on Wed Nov 30, 2011 2:10 pm UTC, edited 1 Re-test Drive 135 DRQ Timeout Timeout from checking Data ReQuest Timeout (DRQ) bit. Re-test Drive 213 2-9 DAM Errors Data Address Mark (DAM) 2-9.

Replace Drive 557 SERVO 2-9 SERVO is data on track location. There could be media errors present on this drive. There are too many errors detected on this drive to be repaired. Replace the drive if the error repeats.

Check your floppy and retest. Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility. Short self-test routine recommended polling time: ( 2) minutes. http://www.techsupportforum.com/forums/f16/solved-what-is-error-status-code-0132-from-data-lifeguard-diagnostics-537960.html sylvester Black Belt Posts: 559Joined: Tue Jul 27, 2004 4:17 am Top Reply with quote by webstaa » Fri Feb 08, 2008 2:07 pm it means that you have the

This may be due to a media error. Self-test supported. and S.M.A.R.T. If the error repeats, replace the drive.

Re-Test Drive 14 Test Suspended A test has been temporarily suspended by the user. http://www.motherboards.org/forums/viewtopic.php?t=104651 Last year there was some concern about a few stubborn bad sectors that couldn't be reallocated. Extended self-test routine recommended polling time: ( 100) minutes. Roger Back to top #15 rotor123 rotor123 Moderator 8,005 posts OFFLINE Gender:Male Location:New Jersey Local time:05:23 AM Posted 04 October 2014 - 08:27 PM Hi Why not download and run

Replace the drive if the error repeats. have a peek at these guys It ran about an hour and came up with Error Code 223, and said it repaired all the problems. Auto Offline data collection on/off support. Re-test Drive 140 DRQ TIMEOUT ECC The drive did not properly respond to test commands.

There may be repairable media errors on a platter. Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test). Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives. check over here This diagnostic tool could not run in quick mode nor repair what it found in extended mode.

use the second link above to find the proper utility, or contact WD tech support if that fails... Replace Drive 218 10+ SERVO Errors SERVO 10+. Please ensure that you are not loading any other DOS level files from the floppy prior to running diagnostic utility.

Replace Drive 216 10+ IDNF Errors Identified Data Not Found (IDNF) 10+.

This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc. When I did a c:\dir it listed the contents of what was my F drive (secondary HDD). No Errors 100 No Errors Found Successful operation. Karlsweldt Mobo-fu Master Posts: 20445Joined: Wed Nov 12, 2003 11:57 amLocation: 07438 Top Display posts from previous: All posts1 day7 days2 weeks1 month3 months6 months1 year Sort by AuthorPost timeSubject

I must use the OLDER version of the diagnostics, so I must go to http://support.wdc.com/product/downl...sid=18&lang=en, but it can only make a bootable floppy disk and I think my floppy drive's heads Please rate the helpfulness of this answer Answers others found helpful Understanding S.M.A.R.T. Although it seems to have been quite reliable in comparison - it survived for five or six years, and even shrugged off a couple of gravity-aided trips from my desktop to http://maxspywareremover.com/western-digital/western-digital-diagnostic-error-code-0007.php Check cabling and retest.

Roger Back to top #9 anonanon anonanon Topic Starter Members 141 posts OFFLINE Gender:Male Local time:04:23 AM Posted 04 October 2014 - 03:32 PM I'm trying to reactivate this thread Replace the drive if the error repeats. An interrupt command to perform a specific task failed to complete. This is a monitoring system, which stores all errors, retries, and power on hours.

M. Re-Test Drive 102 Seek Timeout A Seek command did not complete in the time allotted for its completion. I have a HP computer, can get the specifics if needed. Western Digital hard drive failed Life Guard test, what does it mean?

The day you stop learning, is the day you die! Forster (1909)Barry Schwartz TED Talk: "The Paradox of Choice" (Featuring the True Secret to Happiness) Top yewbie Posts: 208 Joined: Mon Sep 13, 2010 6:35 pm UTC Re: Diagnosing a Kaput