Home > Western Digital > Western Digital Diagnostic Error Codes

Western Digital Diagnostic Error Codes


Re-Test Drive 258 ECC 10+ Error Correction Code. This error may also appear if the floppy has been infected by a hidden virus. Drive should be replaced. This error may have internal and external reasons. http://maxspywareremover.com/western-digital/western-digital-diagnostic-error-0132.php

If ECC occurs, use Data Lifeguard for additional error correction. The same utility and the original code used to lock the drive are necessary to unlock this drive. A case like this could easily cost hundreds of thousands of dollars. There could be media errors present on this drive.

Wd Error Codes

If the errors continue, replace the drive. The drive may not have been accessed properly possibly due to a bad connection. The open file operation will fail with error -1032 (0xfffffbf8).

Retest after checking the connections. Then it will record the fact in the SMART tables that one more "Bad Sector" had to be replaced. Check cabling & retest. Seatools Those tests are done using direct access to the hardware and do not really depend on the nature of the data on the HDD, nor even on the OS installed and

Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test). Western Digital Error Code 0007 Re-test Drive 163 Unknown Error Queued command timed out. It also may be due to a defective connection. I've gotta say even though I was cursing the PC when it failed again, I've enjoyed doing what I've done and the long hours of testing this, testing that etc as

Retest after checking the connections. Offline surface scan supported. Accept the License, Right Click on the drive to test, Pick Diagnostics, The Run the Quick test and the Extended test. One of the simpler types is just a large number of "Bad Sectors" - ones that return read errors when accessed.

Western Digital Error Code 0007

Some vendors use the security feature to ensure the usage of only specific drives in their system, or the drive may have been locked by a user using a third party http://www.tacktech.com/display.cfm?ttid=282 Secondly, this process temporarily ignores the potential future failure of the HDD. Wd Error Codes Further errors indicate a defective drive. Data Lifeguard Diagnostic For Dos It still has a proven history of failing sectors and a depleted stock of Good Spares, so you are increasing your risk of actual HDD failure and data loss.

You may need to rescan to ensure that the repairs were effective. have a peek at these guys use the second link above to find the proper utility, or contact WD tech support if that fails... Re-test Drive 162 READY EXPECTED Timeout from checking busy bit. The information file, which holds the data pertaining to this drive, is corrupted or missing. Western Digital Support

SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity You may also want to reroute your IDE cable away from sources of electronic bus noise such as your CPU, Power Supply, etc. This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested. check over here ECC is a hardware correction technique that corrects errors.

If Selective self-test is pending on power-up, resume after 0 minute delay. Usually this condition is a good reason to replace the HDD before more serious errors emerge, but not always. Actually, you can NOT repair those sectors, but you may be able to permanently make them invisible, and hope that no more develop.

Check cable & retest.

Non-WD drives are not supported. The drive has detected an unstable condition, possibly an incorrect spin speed. That board runs tests on the HDD all the time in the background, and writes any error messages to its own CMOS for later retrieval. (By the way, Enabling SMART Reporting Ten or more instances of information on data positioning and location could not be found.

If the system cannot properly handle a drive running a specific Ultra ATA rate such as ATA100, the data may become corrupted. This may be an anomaly. Re-Test Drive 257 ECC 2-9 Error Correction Code. http://maxspywareremover.com/western-digital/western-digital-diagnostic-error-code-0007.php Return to WDC.com WD Community Contact Us English Product Support My CloudMy BookMy PassportWD Elements & WD TVInternal DrivesWDLabsLegacy & Other Products Downloads WD Software Product Firmware Product Downloads Warranty &