Use the appropriate version. willawake 01-06-2010 01:39 PM Re: wd diag error message other drive did the same. Drive should be replaced. Group: Senior Member Posts: 3,812 Joined: Dec 2008 From: Eden
sminlalSep 6, 2009, 8:01 PM i_hate_flying said: I've just successfully recovered all my critical files! MyWeb AddThis Bookmark Revision History:09.04.2004 - New link to Western Digital - Diagnostic Error Codes. - Kevin Your Name: Your E-Mail: (required) Friend's E-Mail: (required) View Our World Wide Web Customer Check cable & retest. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 46 00 00 00 40 Device Fault; Error: ABRT
Replace the drive if the error repeats. Return to Top Data Lifeguard Tools 2.8 Error Codes Note: If the same error code is encountered more than once after re-testing, please Contact Us for additional assistance. Error code The image I have includes the NTFS recovery version of Getdataback, which is running right now! An interrupt command to perform a specific task failed to complete.
SCT Data Table supported. Please contact the system vendor for the above-mentioned information. try another psu. This error may also appear if the floppy has been infected by a hidden virus.
Replace the drive if the error repeats. People can say "oh I got a few of these and they worked," but that only means the ones they got worked. Please ensure that you are using the version of diagnostic utility corresponding to either newer or older Western Digital drives. jjkusafSep 7, 2009, 5:05 PM to the OP.http://support.wdc.com/warranty/policy.aspMight be of assistance returning your drive.
Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition. If ECC occurs, use Data Lifeguard for additional error correction. Check connections and retest. Further errors indicate a defective drive.
Retest after checking the connections. https://community.wd.com/t/sector-relocation-error-code-0226/13529 It doesn't sound like the typical click of death that people describe, it's softer, more like a cross between hard drive accessing or a small pin against plastic or thin metal. I wonder if there is a way to remap the problematic sectors? Browse other questions tagged hard-drive hardware-failure smart or ask your own question.
The first step I made is running full test using Data Lifeguard Tools. have a peek at these guys This may be an anomaly. willawake 01-07-2010 12:53 PM Re: wd diag error message ok i tested them in my comp and the two new ones passed the extended test and even the user's original hdd This may be an anomaly.
what do you suggest? If Selective self-test is pending on power-up, resume after 0 minute delay. This error may also be related to memory issues. http://maxspywareremover.com/western-digital/western-digital-hdd-error-0226.php Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error.
Check cabling & retest. Drive should be replaced. i4004 01-07-2010 11:20 AM Re: wd diag error message good choices can still be made.
Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test). I'm running Windows XP. Replace the drive. does it pass?
Any Help? There are too many errors detected on this drive to be repaired. Recheck your connections and replace the cable. this content Re-Test Drive 586 DRQ Timeout Data ReQuest Timeout.
Replace your cable and retest. Retest after checking the connections. Several instances of information on data positioning and location could not be found. Drive should be replaced.
Esker" mean? Replace. If a sector in a critical position fails (there are linked lists on any HDD), most if not all of the data on the entire disk will essentially be lost, or This error occurs when the drive could not read Track Zero.
Finding maximum of added fields Integer function which takes every value infinitely often Problems associated with booking flights inside another set of flights? The drive has to be replaced." oh yeah, also see what SMART says via programs such as everest, or speed fan, etc. Check connections and retest. Drive should be replaced.
There are too many errors detected on this drive to be repaired.