Home > Western Digital > Western Digital Diagnostics Error Code 0132

Western Digital Diagnostics Error Code 0132


Retest after checking the connections. This may be due to a media or read/write error. The command set to be executed has timed out. Windows 7 Hi all, I got a boot disk failure error when restarting my PC. weblink

Replace Drive 219 Drive Cable Error Failure during cable test. Replace the drive if the error repeats. Continue to test or exit the test. Check your floppy and retest.

Western Digital Error Codes

Re-Test Drive 116 IDNF Error Address Not Found Error. Re-Test Drive 2 SMART Attribute Over Threshold Self-Monitoring, Analysis, and Reporting Technology (SMART) threshold exceeded condition. Replace Drive 223 Errors Repaired Errors found, but have been repaired successfully. I must use the OLDER version of the diagnostics, so I must go to http://support.wdc.com/product/downl...sid=18&lang=en, but it can only make a bootable floppy disk and I think my floppy drive's heads

Drive should be replaced. Not just that you will save money, you will as well hone your technical skills. Virtual Memory Too Low Another problem that we always experience is connected to the RAM space of our PC. Thanks for the help.

I couldn't find a diagnostic tool that listed that exact drive so I DL'd the one that had all the other JD drives on it... Re-test Drive 135 DRQ Timeout Timeout from checking Data ReQuest Timeout (DRQ) bit. They weren't able to fix my problem, but for a fee they were at least able to tell me that there was apparently nothing wrong with my drive's PCB, and thus http://www.techsupportforum.com/forums/f16/solved-what-is-error-status-code-0132-from-data-lifeguard-diagnostics-537960.html Drive should be replaced.

I'm staring at the System Recovery Options pop-up and there is no OS listed for me to choose. Retest the drive. Re-Test Drive 111 DIAG COMMAND ERROR The drive did not properly respond to test commands. There are too many errors detected on this drive to be repaired.

Western Digital Error Code 0007

Please re-test the drive with Data Lifeguard. http://www.motherboards.org/forums/viewtopic.php?t=104651 What exactly should I try next? (Fortunately there's nothing of particularly great value stored on this drive.) Last edited by Jorpho on Wed Nov 30, 2011 2:10 pm UTC, edited 1 Western Digital Error Codes Sense: No additional sense information[ 80.272940] end_request: I/O error, dev sdb, sector 0[ 80.272951] ata1: EH complete[ 80.277720] sd 0:0:1:0: [sdb] 1953525168 512-byte hardware sectors (1000205 MB)[ 80.277742] sd 0:0:1:0: [sdb] Data Lifeguard Diagnostic For Dos Leave the failing drive in the freezer, run the cables out to the running computer.

The Identify Drive Command has not received an acceptable response from the drive. have a peek at these guys then the hard drive spins up, then clicks a few times (louder than usual drive access, usually 3 clicks) then the drive spins down and starts trying to access the floppy No Errors 100 No Errors Found Successful operation. Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer). Western Digital Support

Retest the drive. Check cable & retest. Re-test Drive 138 Still Busy Timeout Timeout from checking busy bit. http://maxspywareremover.com/western-digital/western-digital-diagnostics-error-code-223.php One possible cause for this is the attack of virus.

If it takes 2 minutes then we know for sure it's the drive. I'm going to install windows on that and get my rig running again. The drive is defect free.

The mere act of pressing the ESC key and the Ctrl + Alt + Del combination is definitely not the solution for this.

Drive should be replaced. Re-Test Drive 115 ICRC Error Ultra DMA CRC error. It may also be due to a defective connection. Re-Test Drive 7 SMART Offline Immediate Command Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) Offline Immediate command failed.

Forster (1909)Barry Schwartz TED Talk: "The Paradox of Choice" (Featuring the True Secret to Happiness) Top Jorpho Posts: 5992 Joined: Wed Dec 12, 2007 5:31 am UTC Location: Canada Re: Diagnosing Re-test Drive 139 DRQ NOT EXPECTED The drive did not properly respond to test commands. Check cabling & retest. http://maxspywareremover.com/western-digital/western-digital-hard-drive-error-code-0132.php Re-test Drive If an error code is encountered that is not in the list above, please Contact Us for additional troubleshooting.

I am not a techie but I can get into my hard drive area using either ERD Commander or using the Seagate and now the WD Diagnostic Data Lifeguard solutions. It also may be due to a defective connection. Blue Screen of Death This Western Digital Error Status Code 0132 doesn't pick an operating system to attack, it can occur to all even in the most up-to-date ones. We use data about you for a number of purposes explained in the links below.

Reinstallation of software which has been affected is your next alternative in case the problem doesn't have to do with viruses.