Home > Western Digital > Western Digital Diagnostics Error Code 223

Western Digital Diagnostics Error Code 223

Contents

It ran about an hour and came up with Error Code 223, and said it repaired all the problems. Replace the drive if the error repeats. I noticed this new drive doesn't come with any ribbon cable. I waited a few hours and pushed on a few cables just to see if that was the problem, then rebooted and WD testing stuff came up again, this time it weblink

Reports: · Posted 5 years ago Top raphoenix Posts: 14920 This post has been reported. Re-test 132 Command Error Command Aborted. Retest. The drive has not responded back in the time allotted.

Western Digital Error Codes

Drive should be replaced. Re-test Drive 134 Busy Timeout Timeout from checking busy bit. Privacy Policy Terms of Use Trademarks Select your Language Language 中文(繁體) 中文(简体) Čeština Deutsch English Español Francais ελληνικά Italiano 日本語 한국어 Polski Português РУССКИЙ Türk Forums Search Forums Recent Posts Members Retest after checking the connections.

ECC is a hardware correction technique that corrects errors. It also may be due to a defective connection. Please re-test the drive with Data Lifeguard. Replace the drive if the error repeats.

Replace Drive 210 Self Test Incomplete SMART Self Test failed to complete (e.g. -- timed out). Western Digital Error Code 0007 Reports: · Posted 5 years ago Top daringjoe Posts: 10 This post has been reported. So yeah, its normal.. Re-Test Drive 17 Erase SSD Failure A write command during the test has failed.

Replace Drive 457 IDNF 2-9 Identified Data Not Found. Self-Monitoring, Analysis, and Reporting Technology (SMART). The snag comes when you leave it off for awhile or have a power surge or loss or it doesn't boot up right somehow....that's where havoc sets in. The Identify Drive Command has not received an acceptable response from the drive.

Western Digital Error Code 0007

This may be due to a media or read/write error. http://www.howtogeek.com/forum/topic/western-digital-wd800ajb-hdd-problem This error can occur on non-Western Digital drives. Western Digital Error Codes Re-test Drive 144 THIRD STROKE ERROR Error encountered during 1/3 stroke seek. I don't really trust the drive because I already lost one file to it, and the drive seems unwilling to set the problem sectors aside.

I backed up the contents of the drive to another system and booted up dlgdiag and did an extended test. http://maxspywareremover.com/western-digital/western-digital-diagnostics-error-codes.php Replace the drive. SolvedRaw Read Errors on brand new Seagate 2TB Internal drive. Ten or more instances of track information could not be found.

There were media errors that were within the repair capabilities of diagnostic utility. Replace Drive 570 No Recalibration Recalibration command failed. This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc. check over here I have a HP computer, can get the specifics if needed.

Moreover, I'm compelled to open up my CPU and I've to disconnect the IDE cable from the drive and reconnect it for the BIOS to be able to detect it in Retest after checking the connections. Re-test with appropriate diagnostic utility 222 Drive Failed the Test The drive has failed the SMART test.

The cable is loose, broken, or not plugged in.

Check cable and retest. It also may be due to a defective connection. May need to run DLGUDMA to set the drive to a slower speed or replace the IDE cable. Re-Test Drive 8 Read Sector Failure A Read command during the test has failed.

Re-test Drive with appropriate diagnostic utility 204 Missing Log File The log file that existed at startup of diagnostic utility has been moved or no longer exists. Reports: · Posted 5 years ago Top LH Posts: 20002 This post has been reported. Track 0 also holds information about the drive. this content Here's the link: WD800AAJB The only difference in the picture is that this drive is Blue.

It also may be due to a defective connection. The Western Digital one is the one that's giving me a hard time. Several instances of track information could not be found. Re-test Drive 220 Drive is Locked Security feature of the drive reports locked status.

The automatic repair feature can attempt a repair if possible. SERVO is data on track location. My question is: Let's suppose, there IS something wrong with the PSU, or the motherboard, or anything, if so, why would my old drive work fine? :S Whereas, this one messes No Errors 15 Read Diagnostics Sector Error A read command during the test has failed.

Drive should be replaced. OH, I added the second drive this summer and it went in fairly well, and all seemed OK, but I left it for around 5 months, and I am finding out,