Home > Western Digital > Western Digital Error 0212 Code

Western Digital Error 0212 Code

If the automatic repair feature is unable to repair these errors, replace the drive. If the error repeats, replace the drive. It also may be due to a defective connection. The information file, which holds the data pertaining to this drive, is corrupted or missing. weblink

enabled help you monitor a drive's internal status through diagnostic commands. Will i be able to do that? oxter 2011-08-07 14:43:55 UTC #2 You can cancel the RMA, you should be able to replace it latter on, if you determent that the Check cabling and retest. F1 before and after http://goo.gl/QByhJ6 http://goo.gl/wCG1Nn BIOS:- http://goo.gl/KZzBWT- http://goo.gl/6sxlaO Smart BOOT (Hiren's Boot USB):- http://goo.gl/vRRQGo HDD Voice: https://soundcloud.com/jojohaha/sets/001-1 wd2500bevt22zct 2014-12-13 14:58:33 UTC #2 WD2500BEVT-22ZCT0 - 250GB HDD - error/status code 0132 https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

ECC is a hardware correction technique that corrects errors. Retest. Ten or more instances of information on data positioning and location could not be found. Replace Drive 219 Drive Cable Error Failure during cable test.

Re-Test Drive 18 Read Verify Sector Ext Error A Read Verify Sector Ext command during the test has failed. Track 0 also holds information about the drive. I got 0007 and 0225 two times. Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test).

There may be media errors present on this drive. Replace Drive 200 Drive Not Tested Supported WD drives are initialized with this status. It also may be due to a defective connection. New Posts Intel 600p vs.

Re-Test Drive 12 Too Many Bad Sectors Detected Error count reached a threshold value. This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested. Yes, my password is: Forgot your password? Replace the drive if the error repeats.

Please re-test the drive with Data Lifeguard. Discover More It also may be due to a defective connection. Re-test with appropriate diagnostic utility 222 Drive Failed the Test The drive has failed the SMART test. Re-test Drive 201 Non-WD Drive The drive does not have a WD serial number.

This may be due to an internal error or to a failed connection which did not allow the interrupt command to be sent to the drive properly. have a peek at these guys Replace Drive 215 2-9 IDNF Errors Identified Data Not Found (IDNF) 2-9. Replace Drive 161 RESET SIGNATURE The drive did not properly respond to test commands. Replace your cable and retest.

It may also happen when the wrong version of diagnostic utility is used. Retest. Re-Test Drive 115 ICRC Error Ultra DMA CRC error. check over here Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer).

One instance of information on data positioning and location could not be found. Replace the drive. Retest.

Replace Drive 218 10+ SERVO Errors SERVO 10+.

Please ensure that you are using the proper version of diagnostic utility. Retest. SERVO is data on track location. Re-Test Drive 19 SMART Enabled Operation Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) Enable Operation failed.

Don't show me this message again. All Rights Reserved. The drive has not responded back in the time allotted. http://maxspywareremover.com/western-digital/western-digital-error-code-120.php Replace the drive if the error repeats.

Replace drive if unable to correct error 120 NO DRIVE FOUND Cannot communicate with drive. Drive should be replaced. The automatic repair feature can attempt a repair if possible. The drive is defective.

Replace Drive 585 Busy Timeout During a read verify, a command could not be completed. Return to Top Data Lifeguard Tools 11 and 10 Error Codes Note: If the same error code is encountered more than once after re-testing, please Contact Us for additional assistance. Several instances of track information could not be found. I installed the WD Smartware software included with the Drive and did a Quick Format using WD Quick Formatter (also included).

Replace Drive 163 Unknown Error Queued command timed out.