Home > Western Digital > Western Digital Error Code 0225

Western Digital Error Code 0225

Replace the drive if the error repeats. SCT capabilities: (0x3037) SCT Status supported. Re-Test Drive 257 ECC 2-9 Error Correction Code. Contact System Vendor 221 Test Not Supported Certain older drives do not support certain SMART Self Tests. weblink

Re-Test Drive 100 Errors Found A Read or Write command during the test has failed. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Press F1 to resume. Recheck your connections and replace the cable. have a peek at this web-site

Running %%860 on an out of support operating system is not an adequate solution to protect against threats. Re-test Drive with appropriate diagnostic utility 205 Aborted By User Test was aborted by the user (Alt-X pressed during a test). Re-test Drive 135 DRQ Timeout Timeout from checking Data ReQuest Timeout (DRQ) bit.

Plan on a new drive. Help me determine the status of my HDD This is a discussion on Help me determine the status of my HDD within the Hard Drive Support forums, part of the Tech Publish Related resources SolvedNeed Help external HDD can't open some data Forum SolvedHow to delete all data from SSD/HDD drives(Fresh start) Forum SolvedExternal HDD Data Loss, CHKDSK Help Forum HDD and Discussion in 'Computer Help' started by lakedude, Dec 5, 2012.

You may also want to reroute your IDE cable away from sources of electronic bus noise such as your CPU, Power Supply, etc. The drive has failed and must be replaced. If the automatic repair feature is unable to repair these errors, replace the drive. Please re-test the drive with Data Lifeguard.

Retest after checking the connections. If DLG is unable to detect your drive, then temporarily reconfigure your SATA controller in your BIOS setup for legacy or IDE compatibility mode. Replace your cable and retest. Re-Test Drive with latest diagnostic utility 117 Uncorrectable ECC Error Uncorrectable Error Correction Code (ECC) Error.

Extended self-test routine recommended polling time: ( 100) minutes. This process simply goes on all the time. There could be media errors present on this drive. Check your floppy and retest.

You may need to rescan to ensure that the repairs were effective. http://maxspywareremover.com/western-digital/western-digital-error-code-120.php Replace the drive if the error repeats. Re-Test Drive 103 Write Fault Error A Write command during the test has failed to complete. Retest and replace the drive if the error repeats.

Replace Drive 357 DAM 2-9 Data Address Mark. Drive should be replaced. Ensure that you are using the latest version of diagnostic utility and that your cable is in good working condition. http://maxspywareremover.com/western-digital/western-digital-error-0225.php Replace the drive if the error repeats.

Thanks in advance, Steve More about : hdd data diagnostics chkdsk conflict Paperdoc a c 464 G Storage 27 March 2012 01:02:04 Chkdsk and Data Lifeguard do different tests, and do Isn't it supposed to be testing the drive itself? Replace Drive 226 Sector Relocation Error Failure to relocate a sector during drive repair.

Auto Offline Data Collection: Enabled.

Replace Drive 208 SMART status failed after the media scan. Re-Test Drive 19 SMART Enabled Operation Failure Self-Monitoring, Analysis, and Reporting Technology (SMART) Enable Operation failed. Ask ! The cloning process took a longer time than normal because it kept finding faulty sectors, but the final clone copy on the new drive apparently had NO errors in it, and

Check cable & retest. lol, that sucks, but that's what the website said. Operating System and Data; plug and go? http://maxspywareremover.com/western-digital/western-digital-hard-drive-error-0225.php SolvedRecover data from windows hdd after reinstall SolvedHDD data after cloning to SSD?

Replace Drive 218 10+ SERVO Errors SERVO 10+. The Quick tests check several easy things, and one of those is to check the SMART data stored on the controller board of the HDD unit itself. As part of the background work, though, that also means that every write will be followed by a read and assessment of the signal quality and data integrity of that sector; Total time to complete Offline data collection: ( 8400) seconds.

It also may be due to a defective connection.