Home > Western Digital > Western Digital Error Code 223

Western Digital Error Code 223


When I had a WD die to read element failure and then too many bad sectors and a smart error, it made it easy to RMA that drive. Replace Drive 584 Diag Command Error During a Quick Test, the sefl-test failed. Re-test Drive with appropriate diagnostic utility 202 Drive Not Supported Older Western Digital drives are not supported by the diagnostic utility version being used. Replace the drive if the error repeats. weblink

Replace Drive 0009 - 0014 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. Ran the WD Data Lifeguard (DLG) from Ultimate Boot CD v5.0.2 and found nothing on Quick test, but found something on Extended test, repaired it and gave error code of 0223. Drive should be replaced. This may be due to a media or read/write error. see here

Western Digital Error Codes

Drive Reliability Monitor. Re-test Drive 213 2-9 DAM Errors Data Address Mark (DAM) 2-9. Replace the drive if the error repeats. Re-Test Drive 8 Read Sector Failure A Read command during the test has failed.

Re-Test Drive 116 IDNF Error Address Not Found Error. The Western Digital one is the one that's giving me a hard time. Retest the drive. No Errors 101 Unknown Error An unknown error has occurred during testing.

daringjoe, see above edit. Western Digital Error Code 0007 Replace the drive if the error repeats. WD CommunityWelcome to the WD Community. https://community.wd.com/t/wd20ears-00s8b1-strange-smart-behavior/14205 Could it be an issue with installing WinXP under FAT32?

Check cabling and retest. Related resources Internal HDD Raw Read Error Rate - Tech Support Raw Read Error Rate Failure and Pending Sectors - Tech Support OCZ Vertex 3 Raw Read Error Rate/Predicted TEC - Re-Test Drive 586 DRQ Timeout Data ReQuest Timeout. This may be due to a media or read error.

Western Digital Error Code 0007

This error may also appear if the floppy has been infected by a hidden virus. http://www.tomshardware.com/forum/250912-32-read-error-rate Replace Drive 457 IDNF 2-9 Identified Data Not Found. Western Digital Error Codes Re-test Drive 145 FULL STROKE ERROR Error encountered during full stroke seek. No Errors 100 No Errors Found Successful operation.

This may be due to a media error. http://maxspywareremover.com/western-digital/western-digital-error-code-201.php All Rights ReservedTom's Hardware Guide ™ close × Questions Documents More Menu Tweet wd error code 223? It also may be due to a defective connection. Check your connections and replace the cable.

There may be media errors present on this drive. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Please contact the system vendor for the above-mentioned information. http://maxspywareremover.com/western-digital/western-digital-error-code-120.php Retest after checking the connections.

Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error. Re-test Drive 135 DRQ Timeout Timeout from checking Data ReQuest Timeout (DRQ) bit. Can't find your answer ?

Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9.

Continue to test or exit the test. WDC Support Downloads Knowledge Base Product Registration Warranty Services Contact Ask a Question Contact Support Feedback Other Sites MyCloud.com Online Learning Center CONNECT WD Blog © 2016 Western Digital Technologies, Inc. Check if the address is correct. This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc.

rijury ... Replace the drive if the error repeats. Please rate the helpfulness of this answer Answers others found helpful Understanding S.M.A.R.T. this content Check cabling and retest.

There may be repairable media errors on a platter. Replace the drive. The drive has not responded in the time allotted. My only concern is how to RMA this when I fill out the RMA.What would I put?  Dlgdiag keeps returning with error code 0223 no matter how many times its run

There are too many errors detected on this drive to be repaired. Thanks for your time and reply, ispalten. :) Reports: · Posted 5 years ago Top ispalten Posts: 6259 This post has been reported. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. This may be due to a defect with the drive or a bad connection.

I can't explain it. Replace Drive 585 Busy Timeout During a read verify, a command could not be completed. open circuit and no speed sensor signal Error 67 503_WD Malfunction or failure of NG-Lo module ... Replace the drive.

You may need to rescan to ensure that the repairs were effective. Open ibaques opened this Issue Feb 25, 2016 · 3 comments Projects None yet Labels ... Some vendors use the security feature to ensure the usage of only specific drives in their system, or the drive may have been locked by a user using a third party Replace the drive if the error repeats.

This may be a drive issue, however it may be related to a defective connection. Re-test the drive with Data Lifeguard. Retest after checking the connections.