Home > Western Digital > Western Digital Error Status Code 0003

Western Digital Error Status Code 0003

Replace the drive. Error logging capability: (0x01)Error logging supported. Drive should be replaced. SERVO is data on track location. http://maxspywareremover.com/western-digital/western-digital-error-code-0003.php

Auto Offline Data Collection: Enabled. Drive should be replaced. Retest after checking the connections. There may be media errors present on this drive. click to read more

At some point, however, the spare pool is exhausted, and no relocation nor remapping can take place. This may be due to a media or read/write error. Incidentally, it is in warranty, but I don't know if WDC has any refurnished RE2 drives available for replacement, although I assume that they would have something. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode.

It also may be due to a defective connection. Instead of logs, Western Digital uses their Super On command to tell the drive to get ready to transfer service area (SA) data. My next idea is to read that data using mhdd. C37 and the other parallel connected capacitors would be the filters for the Vcore supply for the Marvell MCU.

Replace the drive if the error repeats. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. I don't know what the condition of the disk is without seeing full SMART attributes, which you can get in Windows (CLI: smartmontools, GUI: PassMark DiskCheckup or HD Tune Pro) or http://www.manualslib.com/manual/534908/Western-Digital-Wd-Quick-Tester.html?page=17 How can I save this drive...

Maybe yes, maybe no. Retest the drive. The same utility and the original code used to lock the drive are necessary to unlock this drive. Re-test 132 Command Error Command Aborted.

It will be interesting to try! SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. The drive has been working flawlessly till now.3 days ago my normally loud Caviar Black went silent on a reboot, I got a “Master Boot Record error – Press A Key” Re-test Drive 139 DRQ NOT EXPECTED The drive did not properly respond to test commands.

There are hundreds of MOD files, and there is a "0" directory and a "1" directory in the RAR file that I got from datadonor.net, each with a ton of those have a peek at these guys It sounds like you expanded your main storage drive without also expanding your backup drive. This may be due to an internal error or to a failed connection which did not allow the interrupt command to be sent to the drive properly. Conveyance Self-test supported.

Just PM me how much you want and will exchange info. · actions · 2011-Jun-6 10:13 pm · dolphins

dolphins Premium Member 2011-Jun-6 10:33 pm Has anyone heard of these...»www.ultimatebootcd.com/»www.bootdisk.com/ntfs.htmIf so, This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested. Auto Offline data collection on/off support. check over here Replace the drive if the error repeats.

Running %%860 on an out of support operating system is not an adequate solution to protect against threats. Supports SMART auto save timer. Replace Drive 13 Failed to Repair Sector A test failed to repair bad sectors.

This error is most likely an internal malfunction of the drive and not related to the condition of the cables etc.

The drive has not responded in the time allotted. I already have a boot disk that contains MHDD 4.6, although I someone  says to use version 4.5 for some reason. However it's obvious that the vendor is motivated to sell more hard drives. James Litten -- I ran Gsmartcontrol and here is the output on the drive in question.

Family Lines: Western Digital Passport Western Digital Scorpio Western Digital Caviar Western Digital Elements Unanswered Questions Ask a Question Usually answered in minutes! They will not be affected by the MOD data. That number is quite high for a drive which is fairly new. http://maxspywareremover.com/western-digital/western-digital-error-status-code-007.php Update: S.M.A.R.T. === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD10EARS-00Y5B1 Serial Number: WD-WCAV******** LU WWN Device Id: 5 0014ee 259379483 Firmware Version:

Drive should be replaced. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 41 08 27 5c 59 e0 Error: ABRT 8 sectors SCT Feature Control supported. I cloned my 160-GB Seagate Barracuda onto the new drive with Acronis True Image WD Edition.

Wayne 2011-12-21 20:17:12 UTC #3 did you at least replace the cable to make sure that it isn't the cable?  the other thing is that data recovery for raid 0 is Re-Test Drive 258 ECC 10+ Error Correction Code. SERVO is data on track location. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection.

And I guess we are hoping that any further calibration and parameters are safe and sound in negative LBA cylinders on the physical drive? Question about 2TB WD ELEMENTS USB 20DESKTOP EXTERNAL 35IN 1 Answer While it's plugged in to PC in the PC start While it's plugged in to PC in the PC start Error: (09/15/2014 03:38:16 PM) (Source: .NET Runtime) (User: ) Description: Application: DigitalEditions.exe Framework Version: v4.0.30319 Description: The process was terminated due to an unhandled exception. This may be a drive issue, however it may be related to a defective connection.

Error: (10/03/2014 08:24:02 PM) (Source: ESENT) (User: ) Description: wuaueng.dll (3752) SUS20ClientDataStore: Error -1032 (0xfffffbf8) occurred while opening logfile F:\WINDOWS\SoftwareDistribution\DataStore\Logs\edb.log. Thanks.