Home > Western Digital > Western Digital Error/status Code 007

Western Digital Error/status Code 007

I contacted WD and set up a RMA, but thier 'farmed out' support couldn't tell me what the error meant and there was nothing on their web site. This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. Reports: · Posted 5 years ago Top daringjoe Posts: 10 This post has been reported. The cable is loose, broken, or not plugged in. weblink

Retest the drive. The drive has not responded in the time allotted. Replace the drive if the error repeats. Ten or more instances of information on data positioning and location could not be found.

An onboard defect counter has determined the drive has too many errors and should be replaced. Check your floppy and retest. If this were the case, then I'd say the PSU is at fault? "Switches" inside some ensure proper voltage before it powers up possibly. Ten or more instances of track information could not be found.

Thanks for your time and reply, ispalten. :) Reports: · Posted 5 years ago Top ispalten Posts: 6259 This post has been reported. I had them confirm this. My main drive has duplicate files and my other box has two drives with duplicate (but not updated) data. Sharkmanbmw 2010-05-01 01:08:17 UTC #3 I have the exact same issue, black 1TB that fails quick test with status code = 007, failure checkpoint 97 (Unknown Test) It's as though this

The drive has not responded back in the time allotted. Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9. Could even be the motherboard I guess? http://forum.overclock3d.net/showthread.php?t=42603 Several instances of information on data positioning and location could not be found.

Replace the drive. Replace Drive 215 2-9 IDNF Errors Identified Data Not Found (IDNF) 2-9. m 0 l Can't find your answer ? Re-test Drive 143 RANDOM SEEK ERROR Error encountered during random seek.

Replace Drive 163 Unknown Error Queued command timed out. Visit Website It would seem that once the drive comes up it would stay up? Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error. Non-WD drives are not supported.

Replace the drive if the error repeats. have a peek at these guys Check connections and retest. Re-Test Drive 203 DRM Attribute too low beforemedia scan. Ten or more instances of track information could not be found.

If the system cannot properly handle a drive running a specific Ultra ATA rate such as ATA100, the data may become corrupted. Drive should be replaced. Return to Top Data Lifeguard Tools 11 and 10 Error Codes Note: If the same error code is encountered more than once after re-testing, please Contact Us for additional assistance. check over here It also may be due to a defective connection.

Privacy Policy Terms of Use Trademarks Select your Language Language 中文(繁體) 中文(简体) Čeština Deutsch English Español Francais ελληνικά Italiano 日本語 한국어 Polski Português РУССКИЙ Türk Jump to content Sign In Drive should be replaced. I don't think platters are damaged, because a day worked perfectly, and the next day all sectors are delay, perhaps are the heads?Heads are not clicking or nocking, disk noises are

Re-Test Drive 106 Track 0 Error Track 0 was not properly detected.

I ran the quick test both from the Boot CD and later from within Windows and the drive passed the test. Check cabling and retest. A case like this could easily cost hundreds of thousands of dollars. WDC Support Downloads Knowledge Base Product Registration Warranty Services Contact Ask a Question Contact Support Feedback Other Sites MyCloud.com Online Learning Center CONNECT WD Blog © 2016 Western Digital Technologies, Inc.

No problem, raphoenix. Replace your cable and retest. Re-Test Drive 17 Erase SSD Failure A write command during the test has failed. this content If you boot into the BIOS, is the drive seen?

Ten or more instances of information on data positioning and location could not be found. Re-test with appropriate diagnostic utility 0001 - 0008, 0015 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. This may be due to a media or read/write error. If you accept cookies from this site, you will only be shown this dialog once!You can press escape or click on the X to close this box.

There may be media errors present on this drive. Replace Drive 0009 - 0014 SMART Error Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. This may be due to a media error. Check Floppy and use appropriate diagnostic utility 207 Critical Resource Error Unable to locate and/or use a system resource (e.g. - printer).

Ten or more instances of track information could not be found. Re-test and Repair Option diagnostic utility 212 10+ Uncorr ECC Errors Error Correction Code (ECC) 10+. Here is my thread that went nowhere as far as getting any help. Top dick Post subject: Re: WD5000AAKX-001CAO Caviar Blue slow sectors issuePosted: July 19th, 2012, 3:55 Joined: January 8th, 2008, 5:21Posts: 775Location: uk An easy way would be to

Computers with S.M.A.R.T. Some vendors use the security feature to ensure the usage of only specific drives in their system, or the drive may have been locked by a user using a third party Drive should be replaced.