Home > Western Digital > Western Digital Extended Test Error 08

Western Digital Extended Test Error 08


If the cloning does not help, it will not hurt to try to image it.Here is a manual of Acronis: http://support.wdc.com/download/notes/atiwduserguide/ATIH2013WD_userguide_en-US.pdfYou can check 3.7.12 Error handling.Most probably not all the files Drive should be replaced. Check your connections and replace the cable. Replace Drive 225 Too Many Errors Found Error count reached a threshold value. http://maxspywareremover.com/western-digital/western-digital-extended-test-error-code-08.php

Use the appropriate version. Use it to install programs/games too and keep important stuff on new drive. No, create an account now. Check your floppy and retest. http://www.bleepingcomputer.com/forums/t/481210/western-digital-hard-drive-failed-life-guard-test-what-does-it-mean/

Unable To Repair Bad Sectors

Test Time: 07:31:52, October 26, 2009 Test Option: EXTENDED TEST Model Number: WDC WD5000KS-00MNB0 Unit Serial Number: WD-WCANU1419422 Firmware Number: 07.02E07 Capacity: 500.11 GB SMART Status: FAIL Test Result: FAIL Test If there is some physical damage on the drive(physical bad sectors as well) this method may help. Conveyance Self-test supported. It could have been the pending sector and went out as it was reading from it.

Check the drive connections. The system returned: (22) Invalid argument The remote host or network may be down. Replace the drive. Western Digital Error Codes I would not advise you to connect the HDD to other devices or run any other recovery software until you decide that no more data could be recovered through copy-paste.Another thing

All Rights Reserved Tom's Hardware Guide ™ Ad choices Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get For full access please Register. An interrupt command to perform a specific task failed to complete. useful reference It also may be due to a defective connection.

Ten or more instances of information on data positioning and location could not be found. Read Smart Attribute Command Error On Drive 2 and S.M.A.R.T. divJNov 4, 2014, 7:15 PM I have a WD Caviar Blue 500gb. It may also happen when the wrong version of diagnostic utility is used.

Test Error Code 08 Western Digital

At least ten ECC errors have been detected. http://www.tomshardware.com/answers/id-2360746/hdd-die.html Re-Test Drive 112 IRQ Timeout Interrupt ReQuest Interrupt signal not received. Unable To Repair Bad Sectors Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Smart Offline Immediately Command Error On Drive 1 The WD extended test completed in about an hour and produced this report, which doesn't tell me much: Test Option: EXTENDED TEST Model Number: WDC WD5001AALS-00E3A0 Unit Serial Number: WD-WCATR2850613 Firmware

Replace Drive 213 2-9 DAM Errors Data Address Mark (DAM) 2-9. have a peek at these guys Anything else can be done? If it seems better / the same after then go for it. To resolve this issue, try to reseat the drive. Western Digital Quick Drive Test Failed

Blackredgold1964 Test Option: QUICK TEST Model Number: WDC WD1600BEVT-75ZCT0 Unit Serial Number: WD-WXE308H43286 Firmware Number: 11.01A11 Capacity: 160.04 GB SMART Status: PASS Test Result: FAIL Test Error Code: 06-Quick If you do a 3 Pass wipe and the SMART is good go for it. CHKDSK is verifying indexes (stage 2 of 5)... 19 percent completed. check over here It will only fail.

The printer may not be attached or turned on. Status Code 07 Failure Checkpoint 97 Retest the drive. Error logging capability: (0x01)Error logging supported.

Several instances of track information could not be found.

Version 4.12 for older drives and version 5.00 for current drives. Back to top #5 James Litten James Litten Ԁǝǝ˥q BC Advisor 1,928 posts OFFLINE Gender:Male Location:New Jersey Local time:04:27 AM Posted 16 February 2013 - 03:24 PM Hi It Drive should be replaced. Western Digital Bad Sector Repair First of all you need WD diagnostic tool, called " Data Lifeguard Diagnostic" ,  I tried with CD version, IMG was burned ok, at i tried to boot it, but after

Is it dieing? Please re-enable javascript to access full functionality. So maybe I have the wrong driver. this content If you have a question relating the what's going on in the community, we will be happy to respond.