Home > Western Digital > Western Digital Hdd Error Codes

Western Digital Hdd Error Codes

Contents

Re-test Drive 201 Non-WD Drive The drive does not have a WD serial number. The printer may not be attached or turned on. Ten or more instances of track information could not be found. There were too many errors found on this drive to be repaired. weblink

It was lying on a shelf. Replace Drive 161 RESET SIGNATURE The drive did not properly respond to test commands. Replace drive if unable to correct error 118 DAM Error Data Address Mark (DAM) Error. First of all, the hard drive has worked fine for the last 1.5 years. https://support.wdc.com/knowledgebase/answer.aspx?ID=11711

Western Digital Error Code 0007

Re-test Drive 162 READY EXPECTED Timeout from checking busy bit. Further errors indicate a defective drive. This may be due to a media or read/write error.

Rakinos, Apr 25, 2008 Rakinos, Apr 25, 2008 #1 Nov 10, 2010 #2 Cerulean [H]ardForum Junkie Messages: 9,260 Joined: Jul 27, 2006 New Western Digital Blue 160GB IDE HDD and I SCT Feature Control supported. Where can I get a file/list of the common and scientific names of species? Conveyance self-test routine recommended polling time: ( 5) minutes.

Finding a 40GB or larger HD won't be too much of a problem if we can find some an old copy of windows XP. #3 lakedude, Dec 6, 2012 (You Data Lifeguard Diagnostic For Dos I'll put the Speccy output in a separate post. All Rights ReservedTom's Hardware Guide ™ Register Help Remember Me? directory Replace your cable and retest.

It also may be due to a defective connection. Drive should be replaced. SMART is calculated from on-line and off-line drive activity. Now what?

Data Lifeguard Diagnostic For Dos

Replace the drive if the error repeats. http://en.community.dell.com/support-forums/laptop/f/3518/t/19463826 Replace Drive 582 Drive Not Ready Internal communication issue. Western Digital Error Code 0007 SCT Data Table supported. Western Digital Support failure and errors How to test a drive for problems using Data Lifeguard Diagnostics for Windows Where to download software, utilities, firmware updates, and drivers for WD products Processing...

Replace the drive. http://maxspywareremover.com/western-digital/western-digital-error-codes-0201.php Re-Test Drive 100 Errors Found A Read or Write command during the test has failed. Re-test with appropriate diagnostic utility 222 Drive Failed the Test Self-Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART Status/Self Test Command. Re-Test Drive 258 ECC 10+ Error Correction Code.

Re-test the drive with Data Lifeguard. That is because most Windows systems use 4k as the smallest unit of disk measure (a cluster) and the bad sector (which is only .5k) is in that 4k cluster. Replace the drive if the error repeats. check over here Auto Offline data collection on/off support.

Ask ! This may be due to a defect with the drive or the drive may not have responded properly due to a bad connection. to report if a drive has failed, it must be enabled as a system option.

EDIT: No dice.

Running %%860 on an out of support operating system is not an adequate solution to protect against threats. Re-Test Drive 257 ECC 2-9 Error Correction Code. Re-Test Drive 109 DRQ WAS SET The drive did not properly respond to test commands. To start viewing messages, select the forum that you want to visit from the selection below.

Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted. Re-Test Drive 16 Random Read Error A read command during the test has failed. The cable is loose, broken, or not plugged in. this content James Back to top #6 anonanon anonanon Topic Starter Members 141 posts OFFLINE Gender:Male Local time:04:27 AM Posted 27 February 2013 - 11:29 PM James, Sorry for the delay,

There were media errors that were within the repair capabilities of diagnostic utility.