Home > Whirlpool Cabrio > Whirlpool Error F-1

Whirlpool Error F-1

Contents

Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). Transcript The interactive transcript could not be loaded. If no damage to wires and all connectors okay, proceed to step C. Press STOP/CANCEL to clear the display. click site

To Manually unlock the door lock system: 1. Check the MCU by looking for operations of the drive motor and check the drive motor for powered rotations. Door switch/lock unit failure. 1. Open and close the door. 2. https://www.ifixit.com/Answers/View/193013/How+can+I+address+the+F1+error+code

Whirlpool Cabrio F1 Error Code Recall

Then it shuts down. This is the most common Duet washer error code! F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times.

It will try to lock it 6 times before displaying the error. BlakeTube Repair & Reviews 53,760 views 16:07 Washing Machine Diagnostic Test & Error Codes (Cabrio, Bravo, & Kenmore Oasis) - Duration: 1:29. Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the Whirlpool Dryer F1 Error Code Whirpool Duet Front Loading Gas and Electric Dryer Fault Codes PF - Power Failure - PF error code indicates a power failure during the dryer's cycle.

Replace control. Whirlpool Washer Cabrio Recall If there is water in the unit: Verify drain pump operation. Press CANCEL and observe for 1 minute to ensure operation is correct. 2. http://www.partselect.com/JustForFun/Whirlpool-Appliance-Fault-Codes.aspx Check the electrical connections at the pump and make sure the pump is running. 4.

Press 'Stop/Cancel' to clear display. Whirlpool Cabrio F1 Recall 2013 After unplugging your washer, carefully pull the washer away from the wall (watch your drain hose and the two inlet hoses). F10 Motor Control Unit (MCU) heat sink thermal trip If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink Check the pressure switch. 8.

Whirlpool Washer Cabrio Recall

Pic 7: unscrew the control board Unplug all the plugs. http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html This code will also appear if the user presses the START key while the lid is open. Whirlpool Cabrio F1 Error Code Recall D. Whirlpool Cabrio Dryer F1 F9 Oven door lock failure Check wiring to door lock switch (the wire harness may be connected wrong).

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. get redirected here google + facebook twitter Liked Your Experience? If no damage to wires and all connectors okay, proceed to step C. Pic 4: unscrew 3 screws Lift the control panel.This will expose the control board. Whirlpool Cabrio Control Board

Unplug washer or disconnect power. 2. Replace User Interface. If a potential suds lock is detected, the control tries up to 3 times to clean out the unit with a mini-cycle. "SL" is displayed if suds are detected but the navigate to this website If damage is found, replace appropriate part.

F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down. Whirlpool Cabrio Dryer F1 Error Code Recall Working... Check the drive belt and reconnect power and plug unit in.

The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened.

DIYCREATIVESOLUTIONS 133,214 views 7:42 Washer Front load Bellow Diagnostic & Repair, leaking washer Whirlpool, Maytag, Sears, - Duration: 8:11. F1 Board failure Replace control board (also called ERC or clock). Check that the drain pump is working properly. 3. Why Does My Whirlpool Cabrio Washer Says F1 E., Cleveland, TN 37311 1-877-477-7278 AppliancePartsPros.com Customer Service 1-877-477-7278 Email Us Terms of Use Privacy Policy Site Map ©1999 - 2016 AppliancePartsPros.com.

Select 'cancel' and observe for one minute for errors. F11 MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure; repeating under or over voltage, or over current conditions. Check the drain hose and make sure it is not plugged or kinked. 2. http://maxspywareremover.com/whirlpool-cabrio/whirlpool-error-f-32.php Ld Long drain "Ld" flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets.

Press CANCEL and observe for 1 minute to ensure operation is correct. 2. First, unplug the machine, so there is no risk of electric shock. RenewAppliance 264,054 views 2:56 WHIRLPOOL CABRIO CONTROL BOARD VIDEO 1 - Duration: 2:00. as soon as you press start, it shuts right down.

Try unplugging unit for two minutes to see if that fixes error. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 Sheller, P.C. Opening the lid will allow you to redistribute the load to avoid a further off balance error.

Reach up along the inside of the front panel and locate the bottom of the door latch assembly. 4. With this failure, power to the motor controller cannot be turned off by the machine controller.