F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. Iniciar sesión Cargando... Share the good news, like us, and tweet. It will try to lock it 6 times before displaying the error. click site
We can hear the pump kick on and run until it cavitates continuously for a long while before finally displaying the f21 code. If failure occurs during high-speed spin the door unlocks after 3 minutes. 1. check that the washer's water valves are closing all the way and water is not filling into the tub when it shouldn't be. To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch.
Plug in washer or reconnect power. 6. Press PAUSE/CANCEL twice to clear the display. Located on the bottom of the door latch assembly is a tear-drop shaped tab. 5.
Refer to the Water Temperature Sensor section. Esta función no está disponible en este momento. Sign In Register Keep model on this computer temporarily This option is valuable if you expect to revisit Sears PartsDirect using this computer and browser in the future. Whirlpool Duet Dryer Error Codes Check the wire harness connection between the motor control board and the main control board.
Check the drive motor for powered rotations. Whirlpool Duet Reset F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times. If this happens, replace oven control (also called clock or ERC). 2. Opening the lid will allow you to view and redistribute the load.
Check that there are no items blocking the door and it is closing completely. look at this site Make sure the harness does not have a bad connection. • Check the quick disconnect at the motor terminal. Whirlpool Duet Washer Error Codes F21 Door lock mechanism is broken. Whirlpool Duet Washer Error Codes F20 What Your Appliance Error Code Really Means.
Check Door Lock/Switch Assembly for foreign objects Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Failure Join our VIP email list and http://maxspywareremover.com/whirlpool-duet/whirlpool-duet-f99-error.php JPlovesLIFE 25.671 visualizaciones 7:35 Whirlpool duet f21 error fix - Duración: 4:32. Your Duet washer has detected that it is full of soap suds which are difficult to drain. Check the Water Temperature Sensor, Heating Element and Element Relay Check connections to the Sensor, Heating Element and Relay F/06 Drive Motor Tachometer Error The control is unable to properly detect Whirlpool Top Load Washer Error Codes
Iniciar sesión 516 22 ¿No te gusta este vídeo? Possible Causes/Procedure Door lock mechanism is broken or removed from door. The filter had coins, pencils, a wire from a bra, and a piece of cloth that was stuck in the pump impeller vanes. http://maxspywareremover.com/whirlpool-duet/whirlpool-duet-f-error.php benjyspapa 2.420 visualizaciones 4:32 Clean internal drain hose to help eliminate Front and Top Load Washer odor - Duración: 9:37.
Q: What washer has the largest capacity? Whirlpool Washer Error Codes 5d Credit will be issued for the part(s) plus tax, minus shipping charges. Check drain pump. 7.
Press PAUSE/CANCEL twice to clear the display. F8 E2 This indicates there is a problem with the Dispenser System (only on select models).Verify detergent drawer or detergent cartridge is not clogged with detergent. Run a short wash cycle and check for any leaks at the filter cover cap. Whirlpool Duet Washer Error Code F11 With an overfill condition, the beeper repeats a warning every 10 seconds with no time out.
Check the pressure switch. 8. Checked the manual Could not find anything wrong with the Drain Hose? Check that the serial harness at the MCU is not mounted upside down. my review here F06 STEAMER DEFECT The Steamer temperature has not reached the correct value.
If the end of the drain hose is below the water level in the washer, water can siphon out as fast as it goes in. Verify CCU operation by running a Diagnostic Test or any cycle. The drive motor must be hooked up properly or a "CE" error will occur. • Drive motor thermal protector has opened. • Motor controller is not powered or fuse has opened. C.L.S.
Replace the Motor Control Unit. Household power supply is too low. 2. Check Pressure Switch harness for continuity. 2. Cargando...
your washer may need a new main control board. NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. Note: Applies to all F1-E... Check wire harness connections to the pump and Central Control Unit (CCU). 3.
If there are no problems, you usually need to replace the door lock assembly. Check Steamer for continuity (Abnormal =infi nity). 2. Replace switch if defective. 4. The F9E1 long drain error is referring to duration not length.
Check the drain pump filter for foreign objects. Re-apply power and observe for at least one minute. 3. The Steamer will no longer function for any wash cycle and should be replaced. Plug in washer or reconnect power. 4.
Plug in washer or reconnect power. 6.