Home > Whirlpool Duet > Whirlpool Duet Washer Manual Error Codes

Whirlpool Duet Washer Manual Error Codes

Contents

It also means unplug the washer so you don't get electrocuted! F6E2 and F6E3 Errors - Communication fault Communication fault between the main control board (CCU) and the user interface (UI) unplug and check the wire connections between the washer's (CCU) and Washer Water Pump Part #:W10391443 Washer Electronic Control Board Part #:W10551697 This Guide is for Whirpool Duet Washer Core Models: WFW70HE, WFW80HE, WFW81HE, WFW94HE, WFW95HE, WFW96HE, WFW97HE (Non Steam) WFW8640, WFW86HE, Replace control. click site

If there are no problems, you usually need to replace the door lock assembly. Everything I have read on the internet was telling me to order MCU and CCU which did not make sense to me since the interface and diagnostic test was working fine. Reply Timothy says: June 29, 2016 at 11:02 am How do I get from Test mode (C01 - C08) How do I get to the F-mode? Oh, I know— you’ll hear some guys swear it was a bad board because they replaced the such-and-such board and it fixed the problem, so it had to be a bad

Whirlpool Duet Washer Error Codes F21

Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check the electrical connections at the pump and make sure the pump is running. The machine control board may have a bad relay and may need to be replaced. Exclusions apply to products with limited shelf life which includes but are not limited to batteries, smoke detectors or chemical-based products, which must be returned within 90 days of the original

Okay, here’s the part you’ve been waiting for: the Silver Bullet Fix for these elusive and mysterious serial communications errors in Whirlpool-built front-load washers. Press and hold any key for 1 minute to clear R failure code from memory. Close Member Exclusive Not a member? Whirlpool Duet Dryer Error Codes Your Duet washer was not able to lock the door after 6 times… you can't say it didn't try.

The problem is at the harness connection points where the molex connector on the harness connects to the boards at either end. Whirlpool Duet Reset Int The cycle was paused or canceled.The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time. appliance repairappliance trainingUnited Servicers AssociationWhirlpool Washer Post navigation Previous Post Successful Entrepreneur Raises the Bar for Rent To Own BusinessesNext Post The Secret to Profitable Service 14 Comments Add yours rickstv Like ApplianceAssistant on Facebook!

Reply Chip says: November 16, 2014 at 8:10 am I get the diagnostic display started but it goes to f1 1 immediately. Whirlpool Duet Washer Error Codes F02 Overloading the unit may cause this problem. applianceassistant 25,621 views 2:04 Whirlpool washing machine drain pump replacement and diagnostic - Duration: 17:45. See the repair guide to fix it yourself Motor control board, Wiring harness F/11 Serial communication error between main electronic ontrol board and motor control board Check the connections on the

Whirlpool Duet Reset

It should have roughly 16 ohms.

your washer may need a new main control board. Whirlpool Duet Washer Error Codes F21 Excessive suds may also cause delays in draining. Whirlpool Duet Washer Error Codes F20 The good news is Whirlpool Duet washing machines have a diagnostic mode to help troubleshoot what's the problem with your washer.

Communication error between the main control and the motor control. get redirected here Circuit Board Medics 79,179 views 5:13 Whirlpool Duet Washer Diagnostics & Error Codes - Duration: 2:04. ApplianceVideo.com 85,483 views 4:11 New and Improved. If the water inlet valve assembly is defective, replace it. Whirlpool Top Load Washer Error Codes

Make sure the inner drum turns freely. (There may be some magnetic resistance (Magnetic Motor) but there should be no mechanical drag.)) (Duet Washer Motor Check) F8E0 Error - (Steam models) Unplug the connectors on the pump. F8E2 Error Dispenser fault. navigate to this website If the pump checks out to be good, replace the control board.

SL Suds lock The motor controller senses a suds lock condition by analyzing the current draw on the drive motor. Whirlpool Duet Sport Washer Error Codes Full Answer > Filed Under: Washers & Dryers Q: How do you mount Whirlpool Duet washer and dryer to a pedestal? Ashland Ave.

Tell us how to save your model.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed. It locks /unlocks door fine. No subscription fees, no hidden charges! Whirlpool Duet Washer Error Code F11 Press PAUSE/CANCEL twice to clear the display.

fb.me/OqBz8UpJ 4daysago ASTI 2017 Feb 8-11, 2017 save the date! Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) Check the MCU Check the Drive Motor Replace sensor if found defective. http://maxspywareremover.com/whirlpool-duet/whirlpool-duet-washer-error-codes-f01.php A power glitch may cause this error.

Circuit Board Medics can eliminate these errors with upgrades to the CCU. This code will also appear if the user presses the START key while the lid is open. Replace motor controller. Repair or replace any damaged parts.

Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check Drive belt • Check MCU • Check Motor • Check Wire Harness Check the pressure sensing hose for kinks or blockage. RenewAppliance 138,535 views 0:40 W10374126 Motor Control Unit (MCU) Removal & Repair - Duration: 4:03. If there are no problems, you usually need to replace the door lock assembly.

You can change this preference below. Up next Whirlpool Washing Machine Error Codes Diagnosis - Duration: 5:50.