Home > Whirlpool Duet > Whirlpool Duet Washing Machine Error Codes

Whirlpool Duet Washing Machine Error Codes

Contents

Check wire harness connections to the User Interface and the Central Control Unit. 3. Gently pull the tab down about 1/4 inch or until a click is heard. 6. F/10 Motor control board overheated Unplug the washer and check the wiring connections on the motor control board. Check Door Lock/Switch Assembly for foreign objects Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Failure Join our VIP email list and click site

Click here to visit Merchant's home page. Average current trip occurs if there is a 2 second average of current draw greater than 5.55 Amps at the motor windings. Plug in washer or reconnect power. 6. Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. http://applianceassistant.com/Washer-Repair/Duet/Duet-Washer-Error-Codes.php

Whirlpool Duet Washer Error Codes F21

Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3. Door Lock Mechanism broken or removed from the Door Check Door Lock/Switch Assembly Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) Door Lock/Switch Assembly Okay, here’s the part you’ve been waiting for: the Silver Bullet Fix for these elusive and mysterious serial communications errors in Whirlpool-built front-load washers. The wires should be to the left when facing the MCU connectors. 9.

F8 E2 This indicates there is a problem with the Dispenser System (only on select models).Verify detergent drawer or detergent cartridge is not clogged with detergent. A power glitch may cause this error. Press PAUSE/CANCEL two times to clear the display. Whirlpool Duet Dryer Error Codes Verify there is not a siphon problem. 2.

I unplug and then I can unlock door. Try unplugging the washer for a minute and putting the washer through a quick diagnostic test and see what you get… In some cases this can reset the control and buy Unplug the washer and check the large item filter in the drain pump for a clog. http://producthelp.whirlpool.com/Laundry/Washers/Washer_Product_Assistance/Error_codes_in_front_load_washers Door Lock Mechanism broken.

So your Duet washer has a gremlin?! Whirlpool Duet Washer Error Codes F02 Door switch open while door is locked. 1. Starting with Whirlpool, Bosch and Dacor next. Mismatch of User Interface and CCU or corrupted EEPROM. 1.

Whirlpool Duet Reset

F/05 Water Temperature Sensor Error If during the water heating step in wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed,

F06 STEAMER DEFECT The Steamer temperature has not reached the correct value. Whirlpool Duet Washer Error Codes F21 F2 - E1 Keypad cable unplugged F2 - E5 Cancel key drive line open F2 - E6 Cancel key drive line open F3 - E0 Oven temperature sensor (RTD) opened (upper Whirlpool Duet Washer Error Codes F20 Check the drain hose and make sure it is not plugged or kinked. 2.

Replace also the CCU. http://maxspywareremover.com/whirlpool-duet/whirlpool-duet-washing-machine-error-code-lf.php Verify CCU operation by running a Diagnostic Test or any cycle. 6. In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the display is cleared. Check resistance of heating element, if present on this model. (abnormal = infinity) 4. Whirlpool Top Load Washer Error Codes

Sud SUDS LOCK (Overdose of detergent detected during the wash cycle) The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. It locks /unlocks door fine. Electrolux is starting our day off. navigate to this website With this failure, power to the motor controller cannot be turned off by the machine controller.

Check wire harness connections to the User Interface and the Central Control Unit. 3. Whirlpool Duet Sport Washer Error Codes The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. Audible clicks will be heard from the switch.

Make sure the inner drum turns freely. (There may be some magnetic resistance (Magnetic Motor) but there should be no mechanical drag.)) (Duet Washer Motor Check) F8E0 Error - (Steam models)

F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. Check for stuck lock switch. Sign up here Shop Your Way members get $10 in points on any PartsDirect purchase with coupon code SYW10. Whirlpool Duet Washer Error Code F11 F20 NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED.

Ordered new disp. Short circuit of Heater to Ground. Press and hold any key down for 1 minute to clear F5 failure code from memory. my review here If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way.

Checked the manual Could not find anything wrong with the Drain Hose? Check the drain pump filter for foreign objects. I fixed my Duet thanks to you. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.

DudeWhitman 49,081 views 3:56 Troubleshooting the F35 Sud Error Code in the Whirlpool Duet Steam Washer - Duration: 12:49. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds. Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation. applianceassistant 25,621 views 2:04 Whirlpool washing machine drain pump replacement and diagnostic - Duration: 17:45.

Check that: The household water supply is turned on and both the cold and the hot water faucets or valves are fully open. Check calcifi cation of steamer element. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes. Perform Service Cycle to pair the UI and CCU SW. 2.

To return a part, you must first obtain a Return Authorization number by calling 888-205-0966 or visiting our website at www.SearsPartsDirect.com and chat with a Parts Trusted Advisor. Plug in washer or reconnect power. 4. In an event of a return, coupon savings may be deducted from your refund. PUMP DRIVE ERROR The pump driver fails to activate.

I have had several of these become unplugged at the sensor connection at the back of the washer drum. (Duet Washer Temperature Sensor Check) F5E1 Error - Door switch fault. S. Measure insulating resistance of heater between contact and housing (norm. 2 MΩ). NOTE: The door switch/lock unit can be manually unlocked.

If failure remains, disconnect power and replace control. Check mechanical linkage from dispenser motor to the top of the dispenser. 3. Shop Game of Thrones costumes and accessories!