Home > Whirlpool Duet > Whirlpool Error Message Fh

Whirlpool Error Message Fh

Contents

then at other times it will complete the entire wash as if there is nothing wrong, maybe there is a siphoning problem,i will try replacing flow meter __________________ - #8 Verify Drain pump operation 2. Did you clean the screen in the cold water fill valve? Is it possible to get these parts at a storeJon Grella : Yes. click site

Ran it through the diagnostics again with no problems and it worked a number of cycles again without a problem. It had a comb, a key, several paper clips, a pair of (disintegrated) reading glasses, several bolts and screws, and 65 cents in change, among the identifiable stuff. This error code will be displayed if the machine is trying to fill with water but the flow meter doesn’t sense any flow for 30 seconds. Checking other threads it looks like it could be the flow indicator or the pressure switch. http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/400-5-620619-/Whirlpool-F-H-FH-No-Water-Entering-Machine-or-Pressure-Switch-Failure-

What Does Fh Mean On A Whirlpool Washer

Overflow Condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. Concentrated detergents labeled 2x and higher will require a small amount of detergent based on load size.Always follow the manufacturer's recommendations. Jon Grella : Good. It is greatly appreciated.

Sign in to report inappropriate content. Then the HF code again. What does this mean and how can I fix it? Whirlpool Duet Pressure Switch I tried to ensure it was properly connected, but when I pulled the connector plug, a little circuit board came out with some sort of sensor on it.

The time now is 04:53 AM. Whirlpool Duet Flow Meter I unplugged and replugged the wiring harness into the control unit to ensure a good connection. Close Yeah, keep it Undo Close This video is unavailable. http://forum.appliancepartspros.com/washer-repair/19512-whirlpool-duet-error-code-fh.html NOTE: If you choose to connect only to cold water, wash performance may be affected.

Top 6 Reasons Top-Load Washer Won’t Agitate? Whirlpool Duet Diagnostic Mode Reinstall hoses, turn on water, and check for leaks.See the Installation Instructions for details. I think code is either pressure switch or flow meter. Add to Want to watch this again later?

Whirlpool Duet Flow Meter

The manual description of the pressure switch says "If an overfill condition is detected by the pressure switch, the CCU will turn on the drain pump and attempt to stop filling." http://producthelp.whirlpool.com/Laundry/Washers/Washer_Product_Assistance/What_is_an_F20_or_FH_Error_Code_on_my_Front-load_Washer Top 5 Reasons Top-Load Washer Won’t Start? What Does Fh Mean On A Whirlpool Washer Each time I try to run it, it allows water to run for about 30 seconds and then the water is shutoff and the code is displayedJon Grella : Ok greatJon Ghw9150p Errorcodes Since I had similar symptoms about 2 months ago, that ended up being a bad drain pump motor, I tested the motor resistance (OK) and that it was getting voltage (OK),

If a cold water wash is selected, the washer is designed to add hot water to keep the temperature optimal for cold wash performance (75°F +/-10°).If you want to save energy get redirected here Back To Top Posted: Sat Nov 26th, 2005 03:54 pm 19th Post The Student Grasshopper Joined:Fri Nov 25th, 2005 Location: Posts:1 Flavorite Brew: Status: Offline Your link S the computer thinks the pressure switch is failing and will shut the watr off because it doesn't want to over fill the machine and flood your house.Jon Grella : So If you have any trouble finding or ordering the parts or installing the parts, please feel free to email me back here and I will help you more for no additional Fh Error Code Maytag Washer

then at other times it will complete the entire wash as if there is nothing wrong, maybe there is a siphoning problem,i will try replacing flow meter Misterfixall, What was the But that doesn't matter much here.Jon Grella : Try your local store and if they don't have it order it online. It washed a few times after that and then began stopping and displaying the HF code, which I understand is from low water flow. navigate to this website by what i am telling you can you determine if any of these parts are suspect?

Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Whirlpool Duet Error Codes I restarted and skipped past C:05 and it completed the remainder of the diagnostic tests with no error messages. Neither the manual nor tech sheet say how to test this.

Watch Queue Queue __count__/__total__ Find out whyClose Washer Diagnostic & Repair - Error codes FH, F9 - Maytag , Whirlpool MFW9800TQ0 ApplianceVideo.com SubscribeSubscribedUnsubscribe34,40534K Loading...

Logged jimhokie VIP Member Member Since: Oct 2013 Posts: 6 Re: Whirlpool Duet front load washer error code FH « Reply #7 on: October 22, 2013, 09:11:13 PM » Despite the What's New? customer now tells me it reads hf intermitantly +stops after 2minutes in beginning wash. Whirlpool Duet Washer Parts Login | FAQ + Reply to Thread Results 1 to 12 of 12 LinkBack LinkBack URL About LinkBacks Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode

Top 5 Reasons Top-Load Washer Won’t Fill? No--I replaced that and get the exact same symptoms.Since I had similar symptoms about 2 months ago, that ended up being a bad drain pump motor, I tested the motor resistance These hoses have a valve insidethat will close if the water pressure ishigher thantwo gallons per minute; this willshut off the water to the washer.If one of these hoses becomes loose, my review here Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the

customer now tells me it reads hf intermitantly +stops after 2minutes in beginning wash. The cold water barely trickles in. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch Verify there is not a siphon problem Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain Loading...

it could receive an early activation from the pressure switch. 10-15-13,07:08 PM #3 Jim Meadows Member Join Date Nov 2005 State VA Posts 55 Oops, my correct model number is GHW9150P. I restarted the test and skipped over this step so the rest of the tests could be run. All rights reserved.