Home > Whirlpool Duet > Whirlpool F H Error Code

Whirlpool F H Error Code

Contents

I checked the hose going to the pressure switch because I read someplace that that could be a problem and its in good shape. Logged Haroldsappliance.com domain Technician Member Since: Nov 2012 Posts: 2551 Country: Re: Whirlpool Duet Washer HF error code « Reply #5 on: March 18, 2013, 08:54:09 PM » May i ask You can try chatting with one of our friendly associates. I don't have a multimeter to test. http://maxspywareremover.com/whirlpool-duet/whirlpool-fh-error-code.php

I think code is either pressure switch or flow meter. Jon Grella : Good. I don't know what the resistance is supposed to read, maybe some of the other guy's out here, that like to piggy back on me here, have more time to find what is test for flow meter? http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/400-5-620619-/Whirlpool-F-H-FH-No-Water-Entering-Machine-or-Pressure-Switch-Failure-

What Does Fh Mean On A Whirlpool Washer

How do I get the door open? I have the same problem & Whirlpool has been no help. Cause 2 Water Inlet Valve Part Testing Watch this helpful video to determine if this may be the cause of your issue.

Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch Verify there is not a siphon problem Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain We welcome your comments and suggestions. The time now is 04:53 AM. Whirlpool Duet Pressure Switch Published on Jul 10, 2013Service your Maytag Washer that has some of the following problems: Error codes fh, f9By visiting us at http://www.appliancevideo.comTo do the repair use a W10514214 Pressure SwitchMaintenance,

Then the HF code again. Whirlpool Duet Flow Meter then at other times it will complete the entire wash as if there is nothing wrong, maybe there is a siphoning problem,i will try replacing flow meter Misterfixall, What was the Find out more » Total: $31.76 Add to Cart Install Help Watch this helpful video to determine how to install your part. http://www.doityourself.com/forum/electric-large-kitchen-home-appliances/507952-stumped-error-code-fh-whirlpool-duet-front-load-washer.html I also took the plug out of the water pump and cleaned it out.

Thanks for the update too. 04-06-15,02:26 PM #12 DrMoisheP Member Join Date Apr 2015 State Non-US Posts 1 The flow meter has a spinner with a magnet (in which particles could Whirlpool Duet Diagnostic Mode The front and back of the washer has cement-like casing that is a little rough and will definitely smash that tube. If Pause/Cancel does not work: Unplug the washer or disconnect the power for one minute. I'm leaning toward the flowmeter being the problem by process of elimination, but still puzzled how this will prevent water from entering even at the beginning of the cycle before the

Whirlpool Duet Flow Meter

Do you have the exact same model number as Glenn? Using non-HE detergent, or more than the manufacturer's recommended amount of detergent, can cause excessive suds.The excess suds can prevent the washer from detecting theincoming water. What Does Fh Mean On A Whirlpool Washer And if that is all connected then change the control. Ghw9150p Errorcodes Category:Appliance Share this conversation Expert: Jon replied4 years ago.

It would then be covered under the original warranty. get redirected here Since the only steps flagged were those where water was supposed to be added, it sounds like a bad water inlet valve, right? No water detected entering machine or Pressure switch trip not detected. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Fh Error Code Maytag Washer

NOTE: Both hot and cold water must be connected to the washer supply and turned on. Back To Top Posted: Sat Nov 26th, 2005 04:04 pm 20th Post Pegi Fellow, Academy of Sublime Masters of Appliantology Joined:Tue May 3rd, 2005 Location:Wichita Falls, Texas Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. navigate to this website The FH code in the owners manual only talks of a water supply problem, and my washer fills with water before giving the code.

Cause 4 Main Control Board Parts Main Control Board for your Whirlpool Washing Machine RepairClinic Item #1059575 Central control unit. Whirlpool Duet Washer Codes Is the unit draining completely ? Water Inlet Valve Testing – Washing Machine Troubleshooting & Repair - Duration: 2:51.

Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the

This will reboot the computer. You're gonna need the service manual for this washer. ____________________Need parts? Had a repair guy look at it, he said replace the CCU. Whirlpool Duet Washer Parts As background, it quit working a couple of weeks ago and I discovered that the reservoir in the pump was full, and I mean full.

It had a comb, a key, several paper clips, a pair of (disintegrated) reading glasses, several bolts and screws, and 65 cents in change, among the identifiable stuff. Close Yeah, keep it Undo Close This video is unavailable. Call our Parts Department now! 877-803-7957 Back To Top Posted: Tue Aug 23rd, 2005 04:34 pm 7th Post hasson1 Grasshopper Joined:Sat Aug 20th, 2005 Location: Posts:2 Flavorite my review here If you have any trouble finding or ordering the parts or installing the parts, please feel free to email me back here and I will help you more for no additional

click Here to view this post Posted: Thu Nov 17th, 2005 08:58 pm 12th Post HAMMER Lurking at the Threshold Joined: Location: Posts: Flavorite Brew: Status: Offline FOR CODE Remember Me? Up next Whirlpool Washing Machine Error Codes Diagnosis - Duration: 5:50. Is the water pressure less than 10 psi?

I notice that when starting a cycle, the drain pump is running continuously until the error code stops the cycle. No--I replaced that and get the exact same symptoms. Ask Your Own Appliance Question Customer: replied4 years ago. Submitted: 4 years ago.

On my washer, I kept getting HF messages, and found that the reed switch remained open (no conduction), even when a magnet was held against it. Glenn October 10th, 2009,10:29 AM #4 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,865 If you start It seems to happen when it gets to the rinse cycle. The soap scum would still be in the machine.

Then run another cycle. This is an emergency shut down to prevent the washer from overfilling when it reaches 10.5 gallons of water (per manual).